Get Chassis Status 命令详情
更新时间：2025/06/26
在Gitcode上查看源码修订记录
| openUBMC版本号 | 修订日期 | 修订人 | 修订内容 |
|---|---|---|---|
| 25.06 | 2025/06/26 | pengqiang-gs | 初稿，新增命令详情 |
基本信息
功能说明
查询机框以及主电源的状态。 This command returns information regarding the high-level status of the system chassis and main power subsystem.
权限
BasicSetting
命令信息
请求信息
无请求信息
响应信息
| 字节顺序 | 域取值说明 |
|---|---|
| 1 | Completion Code |
| 2 | Current Power State [7] - reserved [6:5] - power restore policy[1] 00b = chassis stays powered off after AC/mains returns 01b = after AC returns, power is restored to the state that was in effect when AC/mains was lost 10b = chassis always powers up after AC/mains returns 11b = unknown [4] - power control fault 1b = Controller attempted to turn system power on or off, but system did not enter desired state. [3] - power fault 1b = fault detected in main power subsystem. [2] 1b = Interlock (chassis is presently shut down because a chassis panel interlock switch is active). (IPMI 1.5) [1] - Power overload 1b = system shutdown because of power overload condition. [0] - Power is on 1b = system power is on 0b = system power is off (soft-off S4/S5 or mechanical off) |
| 3 | Last Power Event [7:5] - reserved [4] - 1b = last ‘Power is on’ state was entered via IPMI command [3] - 1b = last power down caused by power fault [2] - 1b = last power down caused by a power interlock being activated [1] - 1b = last power down caused by a Power overload [0] - 1b = AC failed |
| 4 | Misc. Chassis State [7] - reserved [6] 1b = Chassis Identify command and state info supported (Optional) 0b = Chassis Identify command support unspecified via this command. (The Get Command Support command, if implemented, would still indicate support for the Chassis Identify command) [5:4] - Chassis Identify State. Mandatory when bit [6] = 1b, reserved (return as 00b) otherwise. Returns the present chassis identify state. Refer to the Chassis Identify command for more info. 00b = chassis identify state = Off 01b = chassis identify state = Temporary (timed) On 10b = chassis identify state = Indefinite On 11b = reserved [3] 1b = Cooling/fan fault detected [2] 1b = Drive Fault [1] 1b = Front Panel Lockout active (power off and reset via chassis push-buttons disabled.) [0] 1b = Chassis intrusion active |
| (5) | Front Panel Button Capabilities and disable/enable status (Optional) (“Button” actually refers to the ability for the local user to be able to perform the specified functions via a pushbutton, switch, or other ‘front panel’ control built into the system chassis.) [7] - 1b = Standby (sleep) button disable allowed [6] - 1b = Diagnostic Interrupt button disable allowed [5] - 1b = Reset button disable allowed [4] - 1b = Power off button disable allowed (in the case there is a single combined power/standby (sleep) button, disabling power off also disables sleep requests via that button.) [3] - 1b = Standby (sleep) button disabled [2] - 1b = Diagnostic Interrupt button disabled [1] - 1b = Reset button disabled [0] - 1b = Power off button disabled (in the case there is a single combined power/standby (sleep) button, then this indicates that sleep requests via that button are also disabled.) |
命令样例
样例1：
- 请求：
ipmitool raw 0x00 0x01 - 响应：
00